Downlink Control Information (DCI) channel setting include General Settings, Cross-carrier scheduling, PUSCH scheduling, RA initiation, UL power control, and per-sequence PDCCH transmission configurations.

General Settings

DCI general channel settings.

State

Turns the channel On or Off.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:STATe?
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

Power

Sets the power level, in dB for the selected channel.

Refer to the Output Power Calculation (Downlink) for a description of how the software applies to your power settings.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:POWer <rel_ampl> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:POWer?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:POWer 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:POWer?
Range	-60 to 20 dB
Preset	0
State Saved	Yes
Min	-60
Max	20
Initial S/W Revision	A.20.01

Scrambling

This setting applies to DCI, BCH, CFI, HI, and MCH channels.

Turns scrambling on or off.

Refer to 3GPP TS 36.211.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:SCRambling ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:SCRambling?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:SCRambling ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:SCRambling?
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

PDCCH Allocations

Sets the number of OFDM symbols used for PDCCH in each subframe.

Comma separated 10 inputs for each subframe are available.

Highlight the entire field to quickly set all allocations to the same value.

See 3GPP TS 36.211 Table 6.7-1 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:ALLocations <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:ALLocations?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:ALLocations "3,3,3,3,3,3,3,3,3,3" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:ALLocations?
Range	[Any DL-SCH is BL/CE]: 1-3 (DL BW > 10 RBs) or 2-4 (DL BW <= 10 RBs) BL/CE mode: 1 to min(3, OFDM Start Symbol) for >10 RBs 2 to min(4, OFDM Start Symbol) for <=10 RBs
Couplings	System Bandwidth: Determines the valid range of PDCCH allocations: 1–3 (when DL BW > 10 RBs) 2–4 (when DL BW ≤ 10 RBs) PHICH Duration: When PHICH Duration is set to Extended, PDCCH Allocation must be set to value 3. MCH State: When MCH State is set to On and a MBSFN subframe is assigned, these PDCCH Allocations are also coupled to the PDCCH Allocations in the corresponding subframe(s) for the MCH channel.
Preset	"3,3,3,3,3,3,3,3,3,3"
State Saved	Yes
Initial S/W Revision	A.20.01

Search Space Auto-Assignment

Enables or disables the Search Space Auto-Assignment parameter.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:SSPace:AUTo ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:SSPace:AUTo?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:SSPace:AUTo ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:SSPace:AUTo?
Couplings	Affects Candidate and CCE Offset in DCI TX sequences.
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

OCNG for PDCCH

Turns the OCNG (OFDMA channel-noise generation) for PDCCH on or off.

OCNG is allocated on empty resource element groups in the control channel region (PDFICH/PDCCH/PHICH/Cell-Specific RS). OCNG is pseudo-random data and does not include transport channel coding.

On: Unallocated control region is filled with OCNG.
Off: Unallocated control region is not filled with OCNG.

For details, see 3GPP TS 36.521-1.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:OCNG:PDCCh ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:OCNG:PDCCh?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:OCNG:PDCCh ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:OCNG:PDCCh?
Preset	1
State Saved	Yes
Initial S/W Revision	A.20.01

Cross Carrier Scheduling

Cross carrier scheduling settings for the DCI channel.

CIF Presence

Enables or disables the Carrier Indicator Field (CIF) Presence state in the PDCCH DCI formats.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:CIF:PRESence ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:CIF:PRESence?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:CIF:PRESence OFF RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:CIF:PRESence?
Couplings	Enables PDSCH Start and Scheduling Cell Index when set to ON.
Preset	0
State Saved	Yes
Initial S/W Revision	A.20.01

PDSCH Start

Sets the starting OFDM symbol of the PDSCH for the concerned SCell.

Refer to 3GPP TS 36.211, 36.212, 36.213, and 36.331.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDSCh:STARt <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDSCh:STARt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDSCh:STARt 3 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDSCh:STARt?
Range	1 to 3 (number of downlink bandwidth RBs > 10 RBs) 2 to 4 (number of downlink bandwidth RBs ≤ 10 RBs)
Dependencies	This setting is editable when CIF Presence is ON. Otherwise, this setting is read-only.
Preset	3
State Saved	Yes
Min	1
Max	4
Initial S/W Revision	A.20.01

Scheduling Cell Index

Sets the serving cell index which cell signals the downlink allocations and uplink grants for the concerned secondary cell only when CIF Presence is on.
Refer to 3GPP TS 36.211, 36.212, 36.213 and 36.331.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:SCELl:INDex <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:SCELl:INDex?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:SCELl:INDex 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:SCELl:INDex?
Dependencies	This setting is editable when CIF Presence is ON. Otherwise, this setting is read-only.
Preset	0
State Saved	Yes
Min	0
Max	31
Initial S/W Revision	A.20.01

PUSCH Scheduling Settings

PUSCH scheduling settings for UL grant transmission on PDCCH.

Uplink System Bandwidth

Sets the uplink system bandwidth.

See 3GPP TS 36.211, 36.212, and 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:UL:BANDwidth F14M\|F3M\|F5M\|F10M\|F15M\|F20M [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:UL:BANDwidth?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:UL:BANDwidth F10M RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:UL:BANDwidth?
Notes	Uplink system bandwidth and Resource Blocks. Used for DCI Format 0 (PUSCH scheduling). Auto-set to match DL system bandwidth when changed.
Couplings	Downlink System Bandwidth (auto-coupled)
Preset	F10M
State Saved	Yes
Initial S/W Revision	A.20.01

UE Tx Antenna

Sets the UE Tx Antenna port for the selected DCI channel.

See 3GPP TS 36.211 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:UE:TX:ANTenna PORT0\|PORT1 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:UE:TX:ANTenna?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:UE:TX:ANTenna PORT0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:UE:TX:ANTenna?
Preset	PORT0
State Saved	Yes
Initial S/W Revision	A.20.01

Assigned Processes

This setting applies only to DCI #9 channels.
Sets the numbers of individual HARQ processes, separated by commas (for example, 1,2,3) or a range of HARQ processes (for example, 1-3) to enable specific HARQ processes.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:HARQ:PROCesses:ASSigned <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:HARQ: PROCesses :ASSigned?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:HARQ:PROCesses:ASSigned "0-7" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:HARQ:PROCesses:ASSigned?
Range	0 to 7
Dependencies	Number of HARQ Processes. Controls UE1/UE2 PUSCH TX sequence visibility.
Preset	"0-7"
State Saved	Yes
Initial S/W Revision	A.20.01

UE1 C-RNTI

Sets the radio network temporary identifier (C-RNTI) of PUSCH scheduling information, which is transmitted on PDCCH. Typically, the range for C-RNTI is 1 to 65523, but the software allows 0 to 65535 for added test flexibility. Both decimal and hexadecimal entry formats are allowed.

See 3GPP TS 36.211 and 36.321 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:CRNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:CRNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:CRNTi 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:CRNTi?
Preset	1
State Saved	Yes
Min	0
Max	65535
Initial S/W Revision	A.20.01

UE1 C-RNTI RNTI HEX

Query only

Displays hex representation of UE-RNTI Hex value. Both decimal and hexadecimal entry formats are allowed.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI<n>:PUSCh:UE1:CRNTi:HEX?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:CRNTi:HEX?
Dependencies	Automatically reflects the RNTI decimal value, in hex.
Preset	"0x0001"
State Saved	No
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

UE Uplink Transmission Mode

Sets the transmission mode of PUSCH scheduling information, which is transmitted on PDCCH.

1: Single Antenna Port (Port 10)
2: Single Antenna Port (Port 10) / Closed Loop Spatial Multiplexing

See 3GPP TS 36.211, 36.212, and 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TMODe TM1\|TM2 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TMODe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TMODe TM1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TMODe?
Couplings	Coupled with UE1 Number of Antennas and UE1 Number of Codewords
Preset	TM1
State Saved	Yes
Initial S/W Revision	A.20.01

UE Uplink Number of Antennas

Sets the number of antennas of PUSCH scheduling information, which is transmitted on PDCCH.

In case of Uplink Transmission Mode 1, single antenna port (1 Antenna) is available to set.
In case of Uplink Transmission Mode 2, multiple antenna ports (2 or 4 antennas) are available to set.

See 3GPP TS 36.211, 36.212, and 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:NANTenna AT1\|AT2\|AT4 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:NANTenna?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:NANTenna AT1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:NANTenna?
Dependencies	When UE1 Uplink Transmission Mode is TM2
Preset	AT1
State Saved	Yes
Initial S/W Revision	A.20.01

UE Number of Codewords

Sets the number of codewords of PUSCH scheduling information, which is transmitted on PDCCH.

See 3GPP TS 36.211, 36.212, and 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:NCODeword <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:NCODeword?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:NCODeword 2 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:NCODeword?
Range	Number of codewords: 1 (TM1) 1-2 (TM2)
Dependencies	UE1 Uplink Transmission Mode
Preset	1
State Saved	Yes
Min	1
Max	2
Initial S/W Revision	A.20.01

UE2 C-RNTI

Sets the radio network temporary identifier (C-RNTI) of PUSCH scheduling information, which is transmitted on PDCCH.

Typically, the range for C-RNTI is 1 to 65523, but the software allows 0 to 65535 for added test flexibility. Both decimal and hexadecimal entry formats are allowed.

See 3GPP TS 36.211 and 36.321 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:CRNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:CRNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:CRNTi 2 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:CRNTi?
Preset	2
State Saved	Yes
Min	0
Max	65535
Initial S/W Revision	A.20.01

UE 2 C-RNTI HEX

Query only

Displays hex representation of UE2 C-RNTI value. Both decimal and hexadecimal entry formats are allowed.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI<n>PUSCh:UE2:CRNTi:HEX?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:CRNTi:HEX?
Dependencies	Automatically reflects RNTI decimal value in hex.
Preset	“0x0002”
State Saved	No
Initial S/W Revision	A.20.01

UE Uplink Transmission Mode

Sets the transmission mode of PUSCH scheduling information, which is transmitted on PDCCH.

1: Single Antenna Port (Port 10)
2: Single Antenna Port (Port 10) / Closed Loop Spatial Multiplexing

See 3GPP TS 36.211, 36.212, and 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TMODe TM1\|TM2 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TMODe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TMODe TM1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TMODe?
Couplings	Coupled with UE2 Number of Antennas and UE1 Number of Codewords
Preset	TM1
State Saved	Yes
Initial S/W Revision	A.20.01

UE Uplink Number of Antennas

Sets the number of antennas of PUSCH scheduling information, which is transmitted on PDCCH.

In case of Uplink Transmission Mode 1, single antenna port (1 Antenna) is available to set.
In case of Uplink Transmission Mode 2, multiple antenna ports (2 or 4 antennas) are available to set.

See 3GPP TS 36.211, 36.212, and 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:NANTenna AT1\|AT2\|AT4 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:NANTenna?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:NANTenna AT1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:NANTenna?
Dependencies	UE2 Uplink Transmission Mode
Preset	AT1
State Saved	Yes
Initial S/W Revision	A.20.01

UE Number of Codewords

Sets the number of codewords of PUSCH scheduling information, which is transmitted on PDCCH.

See 3GPP TS 36.211, 36.212, and 36.213 for more information.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:NCODeword <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:NCODeword?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:NCODeword 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:NCODeword?
Range	Number of codewords: 1 (TM1) 1-2 (TM2)
Dependencies	UE2 Uplink Transmission Mode
Preset	1
State Saved	Yes
Min	1
Max	2
Initial S/W Revision	A.20.01

RA Initiation

Random Access (RA) initiation settings.

C-RNTI RA Initiation

Sets the value for the Cell - Radio Network Temporary Identifier (C-RNTI).

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:CRNTi:RA <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:CRNTi:RA?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:CRNTi:RA 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:CRNTi:RA?
Preset	1
State Saved	Yes
Min	1
Max	65523
Initial S/W Revision	A.20.01

C-RNTI RA Intiation HEX

Query only

Displays the hex representation of C-RNTI RA Initiation value. Both decimal and hexadecimal entry formats are allowed.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI<n>:CRNTi:RA:HEX?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:CRNTi:RA:HEX?
Dependencies	Automatically reflects C-RNTI RA Intiation decimal value in hex.
Preset	“0x0001”
State Saved	No
Initial S/W Revision	A.20.01

UL Power Control

Uplink power control RNTI settings.

TPC-PUSCH-RNTI

Sets the value, in decimal for the Radio Network Temporary Identifier (TPC-PUSCH-RNTI).

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI<n>:TPC:PUSCh:RNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI<n>:TPC:PUSCh:RNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:TPC:PUSCh:RNTi 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:TPC:PUSCh:RNTi?
Preset	1
State Saved	Yes
Min	1
Max	65535
Initial S/W Revision	A.20.01

TPC-PUSCH RNTI HEX

Query only

Displays the hex representation of TPC-PUSCH RNTI value. Both decimal and hexadecimal entry formats are allowed.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI<n>:TPC:PUSCh:RNTi:HEX?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:TPC:PUSCh:RNTi:HEX?
Dependencies	Automatically reflects TPC-PUSCH RNTI decimal value in hex.
Preset	"0x0001"
State Saved	No
Initial S/W Revision	A.20.01

TPC-PUCCH-RNTI

Sets the value, in decimal for the Radio Network Temporary Identifier (TPC-PUCCH-RNTI).

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:TPC:PUCCh:RNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:TPC:PUCCh:RNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:TPC:PUCCh:RNTi 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:TPC:PUCCh:RNTi?
Preset	1
State Saved	Yes
Min	1
Max	65535
Initial S/W Revision	A.20.01

TPC-PUCCH RNTI HEX

Query only

Displays hex representation of TPC-PUCCH RNTI value. Both decimal and hexadecimal entry formats are allowed.

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI<n>:TPC:PUCCh:RNTi:HEX?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:TPC:PUCCh:RNTi:HEX?
Dependencies	Automatically reflects TPC-PUCCH RNTI decimal value in hex.
Preset	"0x0001"
State Saved	No
Initial S/W Revision	A.20.01

DCI/PDCCH (DL-SCH Control)

DCI/PDCCH transmission configuration for DL-SCH control (DCI #1 through DCI #8).

Each DCI #n (DL-SCHn Control) uses the same 12-parameter sequence template.
DCI#2 to DCI #8 are available and visible only when state of DL-SCH2 to DL-SCH8 is set to ON.

State

Sets the Subframe state.

This setting is read-only and automatically defined by corresponding DL-SCH when data is set to Auto-Configured Bits.
Otherwise, this setting is editable.

n =1 to 8

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX:STATe?
Dependencies	Data type setting
Preset	Off
State Saved	Yes
Initial S/W Revision	A.20.01

Format

Sets the DCI Format type. Automatically selected by DL-SCH and system settings.

Possible values: 0, 1, 1A, 1B, 1C, 1D, 2, 2A, 2B, 2C, 2D, 3, 3A

Refer to 3GPP TS 36.211, 36.212, and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:FORMat?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX:FORMat?
Dependencies	DL-SCH settings, system configuration
Preset	F1A
State Saved	Yes
Initial S/W Revision	A.20.01

TPC PUCCH

Selects the UE's accumulative Tx Power Control (TPC) PUCCH power step.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:TPCPucch TPC0\|TPC1\|TPC2\|TPC3 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:TPCPucch?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX:TPCPucch TPC0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX:TPCPucch?
Choices	TPC #0, TPC #1, TPC #2, TPC #3
Preset	TPC0
State Saved	Yes
Initial S/W Revision	A.20.01

SRS Request

Sets the SRS request value.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:SRS:REQuest <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:SRS:REQuest?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX:SRS:REQuest 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX:SRS:REQuest?
Choices	0,1
Preset	0
State Saved	Yes
Min	0
Max	1
Initial S/W Revision	A.20.01

Data

Selects PN9, PN15, Auto-Configured Bits, or User Defined Bits for the DCI data contents. Click the > button displayed with this setting to make the selection.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:DATa PN9\|PN15\|ACONfig [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:DATa?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:DATa ACONfig RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:DATa?
Dependencies	Corresponding DL-SCH channel
Preset	ACONfig
State Saved	Yes
Initial S/W Revision	A.20.01

Data User Defined

Displays the Data source for the DCI data contents.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:DATa:USER <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:DATa:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX:DATa:USER "00000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:DATa:USER?
Preset	"00000000"
State Saved	Yes
Initial S/W Revision	A.20.01

Data Size

Sets the payload data size (bits) for DCI.

When Data is set to Auto-Configured Bits, this setting is read-only.

For more details, refer to 3GPP TS 36.212.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:DATa:SIZe <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:DATa:SIZe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:DATa:SIZe 28 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:DATa:SIZe?
Dependencies	Data type
Preset	28
State Saved	Yes
Min	1
Max	100
Initial S/W Revision	A.20.01

RNTI

When Data is set to Auto-Configured Bits, this setting is read-only and auto-defined by DL-SCH. Otherwise settable.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:RNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:RNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:RNTi 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:RNTi?
Dependencies	Data type
Preset	1
State Saved	Yes
Min	0
Max	65535
Initial S/W Revision	A.20.01

Search Space

Sets the search space auto-assignment.

When RNTI = 65535 (SI-RNTI) and Data = Auto-Configured Bits, this setting is set to Common and is read-only.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:SSPace COMM\|UESP [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:SSPace?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:SSPace UESP RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:SSPace?
Choices	Common UE Specific
Dependencies	RNTI value, Data type
Preset	UESP
State Saved	Yes
Initial S/W Revision	A.20.01

Aggregation Level

Selects the aggregation level for the DCI.

Refer to 3GPP TS 36.211 and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:AGGLevel 1\|2\|4\|8 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:AGGLevel?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:AGGLevel 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:AGGLevel?
Choices	1, 2, 4, 8
Couplings	When Search Space is UE Specific, then Aggregation Level is 1,2,4,8. When Search Space is Common, then Aggregation Level is 4,8.
Preset	1
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

Candidate

Sets the DCI candidate number.

When Search Space Auto-Assignment is enabled, this setting is read-only.

Refer to 3GPP TS 36.211 and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:CANDidate?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI1:TX1:CANDidate?
Range	Depends on Search Space and Aggregation Level.
Dependencies	Search Space Auto-Assignment, Search Space, Aggregation Level
Preset	0
State Saved	Yes
Min	0
Max	7
Initial S/W Revision	A.20.01

CCE Offset

Displays the CCE Offset which is automatically calculated by other settings.

Refer to 3GPP TS 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI<n>:TX<seq>:CCE:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI:TX:CCE:OFFSet?
Dependencies	Aggregation Level, Candidate, Search Space
Preset	9
State Saved	Yes
Min	0
Max	1023
Initial S/W Revision	A.20.01

UE DCI #9 (PUSCH Scheduling)

UE1 DCI #9 PUSCH Scheduling transmission configuration.
Each sequence contains 25 parameters for UL scheduling grant on PDCCH.

Process

Query only

Displays the HARQ process number. This is auto-calculated from frame/subframe index.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:PROCess?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX:PROCess?
Preset	0
State Saved	No
Min	0
Max	7
Initial S/W Revision	A.20.01

State

Turns the subframe state for UE1 PUSCH scheduling on or off.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:STATe?
Preset	0
State Saved	Yes
Initial S/W Revision	A.20.01

Format

Query only

Displays the DCI Format. This is always set to Format 0 for PUSCH scheduling.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:FORMat?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX:FORMat?
Dependencies	This setting is not visible when State is OFF.
Preset	"0"
State Saved	No
Initial S/W Revision	A.20.01

Data

Select PN9, PN15, Auto-Configured Bits, or User Defined Bits for the DCI data contents. Click the > button displayed with this setting to make the value selection.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:DATa PN9\|PN15\|ACONfig [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:DATa?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX:DATa ACONfig RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:DATa?
Range	PN9, PN15, Auto-Configured Bits, or User Defined Bits
Dependencies	This setting is not visible when State is OFF.
Preset	ACONfig
State Saved	Yes
Initial S/W Revision	A.20.01

Data User Defined

Displays the Data source for the DCI data contents.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:DATa:USER <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:DATa:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX:DATa:USER "00000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX:DATa:USER?
Dependencies	This setting is not visible when State is OFF.
Preset	"00000000"
State Saved	Yes
Initial S/W Revision	A.20.01

Data Size

Sets the payload data size (bits) for DCI.

For more details, refer to 3GPP TS 36.212.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:DATa:SIZe <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:DATa:SIZe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:DATa:SIZe 28 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:DATa:SIZe?
Dependencies	This setting is not visible when State is OFF. When Data=Auto-Configured Bits, this setting is read-only.
Preset	28
State Saved	Yes
Min	1
Max	1024
Initial S/W Revision	A.20.01

Search Space

Sets the search space.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:SSPace COMM\|UESP [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:SSPace?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:SSPace UESP RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:SSPace?
Choices	Common or UE Specific
Dependencies	This setting is not visible when State is OFF.
Preset	UESP
State Saved	Yes
Initial S/W Revision	A.20.01

Aggregation Level

Selects the aggregation level for DCI.

Refer to 3GPP TS 36.211 and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:AGGLevel 1\|2\|4\|8 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:AGGLevel?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:AGGLevel 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:AGGLevel?
Choices	1, 2, 4, 8
Dependencies	This setting is not visible when State is OFF.
Couplings	When Search Space is UE Specific, then Aggregation Level is 1,2,4,8. When Search Space is Common, then Aggregation Level is 4,8.
Preset	1
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

Candidate

Sets the DCI candidate number.

Refer to 3GPP TS 36.211, 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:CANDidate?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:CANDidate?
Range	Depends on Search Space and Aggregation Level.
Dependencies	This setting is not visible when State is OFF. Search Space Auto-Assignment, Search Space, Aggregation Level
Preset	1
State Saved	Yes
Min	0
Max	7
Initial S/W Revision	A.20.01

CCE Offset

Query only

Displays the CCE Offset which is automatically calculated.

Refer to 3GPP TS 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:CCE:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX:CCE:OFFSet?
Dependencies	This setting is not visible when State is OFF.
Preset	10
State Saved	Yes
Min	0
Max	255
Initial S/W Revision	A.20.01

Hopping Flag

Sets the frequency hopping flag on or off.

See 3GPP TS 36.211, 36.212, and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:HOP:FLAG ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:HOP:FLAG?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:HOP:FLAG OFF RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:HOP:FLAG?
Dependencies	This setting is not visible when State is OFF.
Preset	0
State Saved	Yes
Initial S/W Revision	A.20.01

Hopping RA

Selects the hopping type of PUSCH scheduling information. Parameter choice and hopping bits depend on Uplink System Bandwidth.

See 3GPP TS 36.211, 36.212, and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:HOP:RA HOPA\|HOPB\|HOPC\|HOPD [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:HOP:RA?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:HOP:RA HOPC RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:HOP:RA?
Notes	Parameter choice and hopping bits depend on Uplink System Bandwidth. ()
Dependencies	This setting is not visible when State is OFF.
Preset	HOPC
State Saved	Yes
Initial S/W Revision	A.20.01

RA Type

Sets the resource allocation type.

0: Type 0 (contiguous VRBs)
1: Type 1 (two sets of RBGs)

See 3GPP TS 36.211, 36.212 and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RATYpe <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RATYpe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RATYpe 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RATYpe?
Dependencies	This setting is not visible when State is OFF. DCI Format, Uplink System Bandwidth
Preset	0
State Saved	Yes
Min	0
Max	1
Initial S/W Revision	A.20.01

RB Offset

Sets the resource block offset.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RB:OFFSet <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RB:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RB:OFFSet 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RB:OFFSet?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 5. When Signal Bandwidth is 3 MHz= RB Size max is 14. When Signal Bandwidth is 5 MHz= RB Size max is 24. When Signal Bandwidth is 10 MHz= RB Size max is 49. When Signal Bandwidth is 15 MHz= RB Size max is 74. When Signal Bandwidth is 20 MHz= RB Size max is 99.
Dependencies	This setting is not visible when State is OFF.
Preset	0
State Saved	Yes
Min	0
Max	99
Initial S/W Revision	A.20.01

RB Size

Sets the resource block size.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RB:NUMBer <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RB:NUMBer?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RB:NUMBer 50 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RB:NUMBer?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 6. When Signal Bandwidth is 3 MHz= RB Size max is 15. When Signal Bandwidth is 5 MHz= RB Size max is 25. When Signal Bandwidth is 10 MHz= RB Size max is 50. When Signal Bandwidth is 15 MHz= RB Size max is 75. When Signal Bandwidth is 20 MHz= RB Size max is 100.
Dependencies	This setting is not visible when State is OFF.
Preset	50
State Saved	Yes
Min	1
Max	100
Initial S/W Revision	A.20.01

RBG Start #1 (S0)

Sets the starting RBG index of cluster #1 (s0).

See 3GPP TS 36.211, 36.212, 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RBG:STARt:ONE <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RBG:STARt:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RBG:STARt:ONE 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RBG:STARt:ONE?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 4. When Signal Bandwidth is 3 MHz= RB Size max is 6. When Signal Bandwidth is 5 MHz= RB Size max is 11. When Signal Bandwidth is 10 MHz= RB Size max is 15. When Signal Bandwidth is 15 MHz= RB Size max is 17. When Signal Bandwidth is 20 MHz= RB Size max is 23.
Dependencies	This setting is not visible when State is OFF. This setting is enabled when RA Type = 1. Constraint: s0 < s1 < s2 < s3.
Preset	1
State Saved	Yes
Min	1
Max	23
Initial S/W Revision	A.20.01

RBG End #1 (S1-1)

Sets the ending RBG index of cluster #1 (s1-1).

See 3GPP TS 36.211, 36.212, 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RBG:END:ONE <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RBG:END:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RBG:END:ONE 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RBG:END:ONE?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 4. When Signal Bandwidth is 3 MHz= RB Size max is 6. When Signal Bandwidth is 5 MHz= RB Size max is 11. When Signal Bandwidth is 10 MHz= RB Size max is 15. When Signal Bandwidth is 15 MHz= RB Size max is 17. When Signal Bandwidth is 20 MHz= RB Size max is 23.
Dependencies	This setting is not visible when State is OFF. This setting is enabled when RA Type = 1. Constraint: s0 < s1 < s2 < s3.
Preset	1
State Saved	Yes
Min	1
Max	23
Initial S/W Revision	A.20.01

RBG Start #2 (S2)

Sets the starting RBG index of cluster #2 (s2).

See 3GPP TS 36.211, 36.212, 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RBG:STARt:TWO <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RBG:STARt:TWO?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RBG:STARt:TWO 3 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RBG:STARt:TWO?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 6. When Signal Bandwidth is 3 MHz= RB Size max is 8. When Signal Bandwidth is 5 MHz= RB Size max is 13. When Signal Bandwidth is 10 MHz= RB Size max is 17. When Signal Bandwidth is 15 MHz= RB Size max is 19. When Signal Bandwidth is 20 MHz= RB Size max is 25.
Dependencies	This setting is not visible when State is OFF. This setting is enabled when RA Type = 1. Constraint: s0 < s1 < s2 < s3. RA Type, Uplink System Bandwidth
Preset	3
State Saved	Yes
Min	1
Max	25
Initial S/W Revision	A.20.01

RBG End #2 (S3-1)

Sets the ending RBG index of cluster #2 (s3-1).

See 3GPP TS 36.211, 36.212, 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RBG:END:TWO <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:RBG:END:TWO?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RBG:END:TWO 3 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:RBG:END:TWO?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 6. When Signal Bandwidth is 3 MHz= RB Size max is 8. When Signal Bandwidth is 5 MHz= RB Size max is 13. When Signal Bandwidth is 10 MHz= RB Size max is 17. When Signal Bandwidth is 15 MHz= RB Size max is 19. When Signal Bandwidth is 20 MHz= RB Size max is 25.
Dependencies	This setting is not visible when State is OFF. This setting is enabled when RA Type = 1. Constraint: s0 < s1 < s2 < s3. RA Type, Uplink System Bandwidth
Preset	3
State Saved	Yes
Min	1
Max	25
Initial S/W Revision	A.20.01

MCS Index ()

Sets the modulation and coding scheme of transmission in the selected subframe.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:MCS:ONE 0\|1\|2\|3\|4\|5\|6\|7\|8\|9\|10\|11\|12\|13\|14\|15\|16\|17\|18\|19\|20\|21\|22\|23\|24\|25\|26\|27\|28\|29\|30\|31 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:MCS:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:MCS:ONE 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:MCS:ONE?
Dependencies	This setting is not visible when State is OFF.
Preset	1
State Saved	Yes
Min	0
Max	31
Initial S/W Revision	A.20.01

NDI ()

Sets new data indicator of the transmission in the selected subframe.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:NDI:ONE ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:NDI:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:NDI:ONE OFF RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:NDI:ONE?
Dependencies	This setting is not visible when State is OFF.
Preset	OFF
State Saved	Yes
Initial S/W Revision	A.20.01

TPC PUSCH

Selects the TPC command for PUSCH in the selected subframe.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:TPC:PUSCh TPC0\|TPC1\|TPC2\|TPC3 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:TPC:PUSCh?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:TPC:PUSCh TPC0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:TPC:PUSCh?
Choices	TPC #0, TPC #1, TPC #2, TPC #3.
Dependencies	This setting is not visible when State is OFF.
Preset	TPC0
State Saved	Yes
Initial S/W Revision	A.20.01

Cyclic Shift

Sets the cyclic shift for DM-RS and OCC index.

See 3GPP TS 36.211, 36.212 and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:CYCLic:SHIFt <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:CYCLic:SHIFt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:CYCLic:SHIFt 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:CYCLic:SHIFt?
Dependencies	This setting is not visible when state is OFF.
Preset	0
State Saved	Yes
Min	0
Max	7
Initial S/W Revision	A.20.01

CSI Request

Sets the CSI Request state of the transmission in the selected subframe.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:CSI:REQuest <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:CSI:REQuest?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:CSI:REQuest 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:CSI:REQuest?
Notes	This setting is not visible when State is OFF.
Preset	0
State Saved	Yes
Min	0
Max	1
Initial S/W Revision	A.20.01

SRS Request

Sets the SRS request of PUSCH scheduling information. Range depends on DCI Format.

See 3GPP TS 36.211, 36.212, 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:SRS:REQuest <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:SRS:REQuest?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:SRS:REQuest 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX1:SRS:REQuest?
Range	Depends on DCI Format.
Dependencies	This setting is not visible when State is OFF. DCI Format, Search Space
Preset	0
State Saved	Yes
Min	0
Max	1
Initial S/W Revision	A.20.01

UE DCI #13 (PUSCH Scheduling)

UE2 DCI #13 PUSCH Scheduling transmission configuration.
Same structure as UE1 DCI #9 with 25 parameters per sequence.

Process

Query only

Displays the HARQ process number. Automatically calculated from frame/subframe index.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:PROCess?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX:PROCess?
Dependencies	This setting is not visible when State is OFF.
Preset	0
State Saved	No
Initial S/W Revision	A.20.01

State

Turns the subframe state on or off.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:STATe?
Preset	Off
State Saved	Yes
Initial S/W Revision	A.20.01

Format

Query only

Displays the DCI Format. Always set to Format 0 for PUSCH scheduling.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE1:TX<seq>:FORMat?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE1:TX:FORMat?
Dependencies	This setting is not visible when State is OFF.
Preset	"0"
State Saved	No
Initial S/W Revision	A.20.01

Data

Selects PN9, PN15, Auto-Configured Bits or User Defined Bits for the DCI data contents.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:DATa PN9\|PN15 \|ACONfig [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:DATa?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:DATa ACONfig RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:DATa?
Dependencies	This setting is not visible when State is OFF.
Preset	ACONfig
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Data User Defined

Sets User Defined Bits for the DCI data contents.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:DATa:USER<string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:DATa:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX:DATa:USER "0000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:DATa:USER?
Dependencies	This setting is not visible when State is OFF.
Preset	"00000000"
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Data Size

Sets the payload data size (bits) for DCI.

For details, refer to 3GPP TS 36.212.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:DATa:SIZe <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:DATa:SIZe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:DATa:SIZe 28 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:DATa:SIZe?
Dependencies	This setting is not visible when state is OFF. Read-only when data is Auto-configured bits.
Preset	28
State Saved	Yes
Min	1
Max	100
Initial S/W Revision	A.20.01

Search Space

Sets the search space.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:SSPace COMM\|UESP [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:SSPace?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:SSPace UESP RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:SSPace?
Choices	Common, UE Specific
Dependencies	This setting is not visible when State is OFF.
Preset	UE Specific
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Aggregation Level

Selects the aggregation level.

Refer to 3GPP TS 36.211 and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:AGGLevel 1\|2\|4\|8 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:AGGLevel?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:AGGLevel 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:AGGLevel?
Choices	1, 2, 4, 8. When Search Space is UE Specific, then Aggregation Level options available are 1,2,4,8. When Search Space is Common, then Aggregation Level options available are 4,8.
Dependencies	This setting is not visible when State is OFF.
Preset	1
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

Candidate

Sets the DCI candidate number.

Range depends on Search Space and Aggregation Level.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:CANDidate?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:CANDidate?
Notes	Range depends on Search Space and Aggregation Level.
Dependencies	This setting is not visible when State is OFF.
Preset	1
State Saved	Yes
Min	0
Max	7
Initial S/W Revision	A.20.01

CCE Offset

Query only

Displays the CCE Offset which is automatically calculated.

Refer to 3GPP TS 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:CCE:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:CCE:OFFSet?
Dependencies	This setting is not visible when State is OFF.
Preset	10
State Saved	Yes
Min	0
Max	255
Initial S/W Revision	A.20.01

Hopping Flag

Sets the frequency hopping flag on or off.

See 3GPP TS 36.211, 36.212, and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:HOP:FLAG ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:HOP:FLAG?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:HOP:FLAG OFF RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:HOP:FLAG?
Notes	Click the check box to set the frequency hopping flag on or off. See 3GPP TS 36.211, 36.212 and 36.213.
Dependencies	This setting is not visible when State is OFF.
Preset	OFF
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Hopping RA

Selects the hopping type of PUSCH scheduling information. Parameter choice and hopping bits depend on Uplink System Bandwidth.

See 3GPP TS 36.211, 36.212 and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:HOP:RA HOPA\|HOPB\|HOPC\|HOPD [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:HOP:RA?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX:HOP:RA HOPC RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:HOP:RA?
Dependencies	This setting is not visible when State is OFF.
Preset	HOPC
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

RA Type

Sets the resource allocation type.

0: Type 0 (contiguous VRBs)
1: Type 1 (two sets of RBGs)

See 3GPP TS 36.211, 36.212, and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RATYpe <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RATYpe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RATYpe 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RATYpe?
Dependencies	This setting is not visible when state is OFF.
Preset	0
State Saved	Yes
Min	0
Max	1
Initial S/W Revision	A.20.01

RB Offset

Sets the resource block offset.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RB:OFFSet <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RB:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RB:OFFSet 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RB:OFFSet?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 5 When Signal Bandwidth is 3 MHz= RB Size max is 14 When Signal Bandwidth is 5 MHz= RB Size max is 24 When Signal Bandwidth is 10 MHz= RB Size max is 49 When Signal Bandwidth is 15 MHz= RB Size max is 74 When Signal Bandwidth is 20 MHz= RB Size max is 99
Dependencies	This setting is not visible when State is OFF.
Preset	0
State Saved	Yes
Min	0
Max	99
Initial S/W Revision	A.20.01

RB Size

Sets the resource block size.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RB:NUMBer <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RB:NUMBer?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RB:NUMBer 50 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RB:NUMBer?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 6 When Signal Bandwidth is 3 MHz= RB Size max is 15 When Signal Bandwidth is 5 MHz= RB Size max is 25 When Signal Bandwidth is 10 MHz= RB Size max is 50 When Signal Bandwidth is 15 MHz= RB Size max is 75 When Signal Bandwidth is 20 MHz= RB Size max is 100
Dependencies	This setting is not visible when State is OFF.
Preset	50
State Saved	Yes
Min	1
Max	100
Initial S/W Revision	A.20.01

RBG Start #1 (S0)

Sets the starting RBG index of cluster #1 (s0).

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RBG:STARt:ONE <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RBG:STARt:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RBG:STARt:ONE 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RBG:STARt:ONE?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 4 When Signal Bandwidth is 3 MHz= RB Size max is 6 When Signal Bandwidth is 5 MHz= RB Size max is 11 When Signal Bandwidth is 10 MHz= RB Size max is 15 When Signal Bandwidth is 15 MHz= RB Size max is 17 When Signal Bandwidth is 20 MHz= RB Size max is 23
Dependencies	This setting is not visible when State is OFF. Enabled when RA Type = 1. Constraint: s0 < s1 < s2 < s3. See 3GPP TS 36.211, 36.212, 36.213.
Preset	1
State Saved	Yes
Min	1
Max	23
Initial S/W Revision	A.20.01

RBG End #1 (S1-1)

Sets the ending RBG index of cluster #1 (s1-1).

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RBG:END:ONE <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RBG:END:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RBG:END:ONE 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RBG:END:ONE?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 4 When Signal Bandwidth is 3 MHz= RB Size max is 6 When Signal Bandwidth is 5 MHz= RB Size max is 11 When Signal Bandwidth is 10 MHz= RB Size max is 15 When Signal Bandwidth is 15 MHz= RB Size max is 17 When Signal Bandwidth is 20 MHz= RB Size max is 23
Dependencies	This setting is not visible when State is OFF. Enabled when RA Type = 1. Constraint: s0 < s1 < s2 < s3. See 3GPP TS 36.211, 36.212, 36.213.
Preset	1
State Saved	Yes
Min	1
Max	23
Initial S/W Revision	A.20.01

RBG Start #2 (S2)

Sets the starting RBG index of cluster #2 (s2).

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RBG:STARt:TWO <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RBG:STARt:TWO?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RBG:STARt:TWO 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RBG:STARt:TWO?
Notes	When Signal Bandwidth is 1.4 MHz= RB Size max is 6 When Signal Bandwidth is 3 MHz= RB Size max is 8 When Signal Bandwidth is 5 MHz= RB Size max is 13 When Signal Bandwidth is 10 MHz= RB Size max is 17 When Signal Bandwidth is 15 MHz= RB Size max is 19 When Signal Bandwidth is 20 MHz= RB Size max is 25
Dependencies	This setting is not visible when State is OFF. Enabled when RA Type = 1. Constraint: s0 < s1 < s2 < s3. See 3GPP TS 36.211, 36.212, 36.213.
Preset	3
State Saved	Yes
Min	1
Max	25
Initial S/W Revision	A.20.01

RBG End #2 (S3-1)

Sets the ending RBG index of cluster #2 (s3-1).

See 3GPP TS 36.211, 36.212, 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RBG:END:TWO <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:RBG:END:TWO?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RBG:END:TWO 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:RBG:END:TWO?
Notes	Enter the ending RBG index of cluster #2 (s3-1). Active when RA Type = 1. Constraint: s0 < s1 < s2 < s3. See 3GPP TS 36.211, 36.212, 36.213. When Signal Bandwidth is 1.4 MHz= RB Size max is 6 When Signal Bandwidth is 3 MHz= RB Size max is 8 When Signal Bandwidth is 5 MHz= RB Size max is 13 When Signal Bandwidth is 10 MHz= RB Size max is 17 When Signal Bandwidth is 15 MHz= RB Size max is 19 When Signal Bandwidth is 20 MHz= RB Size max is 25
Dependencies	This setting is not visible when state is OFF. Enabled when RA Type = 1. Constraint: s0 < s1 < s2 < s3.
Preset	3
State Saved	Yes
Min	1
Max	25
Initial S/W Revision	A.20.01

MCS Index ()

Sets modulation and coding scheme of transmission in the selected subframe.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:MCS:ONE 0\|1\|2\|3\|4\|5\|6\|7\|8\|9\|10\|11\|12\|13\|14\|15\|16\|17\|18\|19\|20\|21\|22\|23\|24\|25\|26\|27\|28\|29\|30\|31 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:MCS:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:MCS:ONE 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:MCS:ONE?
Dependencies	This setting is not visible when State is OFF.
Preset	1
State Saved	Yes
Min	0
Max	31
Initial S/W Revision	A.20.01

NDI ()

Sets new data indicator of the transmission in the selected subframe.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:NDI:ONE ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:NDI:ONE?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:NDI:ONE OFF RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:NDI:ONE?
Dependencies	This setting is not visible when State is OFF.
Preset	OFF
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

TPC PUSCH

Selects the TPC command for PUSCH in the selected subframe.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:TPC:PUSCh TPC0\|TPC1\|TPC2\|TPC3 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:TPC:PUSCh?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:TPC:PUSCh TPC0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:TPC:PUSCh?
Choices	TPC #0, TPC #1, TPC #2, TPC #3
Dependencies	This setting is not visible when State is OFF.
Preset	TPC0
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Cyclic Shift

Sets the cyclic shift for DM-RS and OCC index.

See 3GPP TS 36.211, 36.212 and 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:CYCLic:SHIFt <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:CYCLic:SHIFt?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:CYCLic:SHIFt 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:CYCLic:SHIFt?
Dependencies	This setting is not visible when State is OFF.
Preset	0
State Saved	Yes
Min	0
Max	7
Initial S/W Revision	A.20.01

CSI Request

Sets CSI Request state of the transmission in the selected subframe.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:CSI:REQuest <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:CSI:REQuest?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:CSI:REQuest 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:CSI:REQuest?
Dependencies	This setting is not visible when State is OFF.
Preset	0
State Saved	Yes
Min	0
Max	1
Initial S/W Revision	A.20.01

SRS Request

Sets the SRS request of PUSCH scheduling information.

Range depends on DCI Format.

See 3GPP TS 36.211, 36.212, 36.213.

n =1 to 8

seq= 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:SRS:REQuest <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PUSCh:UE2:TX<seq>:SRS:REQuest?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:SRS:REQuest 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PUSCh:UE2:TX1:SRS:REQuest?
Dependencies	This setting is not visible when State is OFF.
Preset	0
State Saved	Yes
Min	0
Max	1
Initial S/W Revision	A.20.01

DCI #/10PDCCH

DCI #10 (RA Initiation) transmission configuration.
Extends the base DCI/PDCCH template with VRB Type, RB Assignment, Preamble Index, and PRACH Mask Index.

DCI #10 is only available when the current component cell is set to be the primary cell.

Refer to 3GPP TS 36.213.

State

Turns the subframe state on or off.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:STATe?
Preset	0
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Format

Query only

DCI Format type. Automatically selected by system settings.

Refer to 3GPP TS 36.211, 36.212, and 36.213.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:FORMat?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:FORMat?
Notes	DCI Format type. Automatically selected by system settings. Refer to 3GPP TS 36.211, 36.212, and 36.213.
Dependencies	If State is ON and Data is Auto-Configured Bits, then Format setting is visible.
Preset	F1A
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Data

Sets or displays the Data.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:DATa PN9\|PN15\|ACONfig [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:DATa?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:DATa PN9 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:DATa?
Notes	Use the Data Source Selection dialog box to select PN9, PN15 or Auto-Configured Bits.
Dependencies	If State is ON, then this setting is visible.
Preset	ACONfig
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Data User Defined

Set or displays the Data.

Here seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:DATa:USER <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:DATa:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:DATa:USER "00000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:DATa:USER?
Notes	Use the Data Source Selection dialog box to select User Defined Bits.
Dependencies	If State is ON, then this setting is visible.
Preset	"00000000"
State Saved	Yes
Initial S/W Revision	A.20.01

Data Size

Sets the payload data size (bits) for DCI.

Refer to 3GPP TS 36.212.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:DATa:SIZe <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:DATa:SIZe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:DATa:SIZe 28 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:DATa:SIZe?
Dependencies	If State is ON, then this setting is visible. It is read-only if Data is Auto-configured Bits.
Preset	28
State Saved	Yes
Min	1
Max	100
Initial S/W Revision	A.20.01

RNTI

Radio Network Temporary Identifier.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:RNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:RNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:RNTi 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:RNTi?
Dependencies	If State is ON, then this setting is visible. It is read-only if Data is Auto-configured Bits.
Preset	1
State Saved	Yes
Min	0
Max	65535
Initial S/W Revision	A.20.01

Search Space

Sets the search space.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:SSPace COMM\|UESP [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:SSPace?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:SSPace UESP RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:SSPace?
Choices	Common, UE Specific.
Dependencies	If State is ON, then this setting is visible.
Preset	UESP
State Saved	Yes
Initial S/W Revision	A.20.01

Aggregation Level

Selects the aggregation level.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:AGGLevel 1\|2\|4\|8 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:AGGLevel?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:AGGLevel 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:AGGLevel?
Choices	1, 2, 4, 8 When Search Space is UE Specific, then Aggregation Level choices are 1,2,4,8. When Search Space is Common, then Aggregation Level choices are 4,8.
Dependencies	If State is ON, then this setting is visible.
Preset	1
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

Candidate

Sets the DCI candidate number.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:CANDidate?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:CANDidate?
Preset	1
State Saved	Yes
Min	0
Max	7
Initial S/W Revision	A.20.01

CCE Offset

CCE Offset automatically calculated. Refer to 3GPP TS 36.213.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:CCE:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:CCE:OFFSet?
Dependencies	If State is ON, then this setting is visible.
Preset	10
State Saved	Yes
Min	0
Max	1023
Initial S/W Revision	A.20.01

VRB Type

Query only

Virtual Resource Block type.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:VRBType?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:VRBType?
Possible Values	Localized, Distributed
Dependencies	If State is ON and Data is Auto-Configured Bits, then this setting is visible.
Preset	LOC
State Saved	No
Initial S/W Revision	A.20.01

RB Assignment

Query only

Resource block assignment bitmap.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:RB:ASSign? (Query Only)
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:RB:ASSign?
Dependencies	If State is ON and Data is Auto-Configured Bits , then this setting is visible.
Preset	"111111111"
State Saved	No
Initial S/W Revision	A.20.01

Preamble Index

Sets the preamble index for RA initiation.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:PREamb:INDex <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:PREamb:INDex?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:PREamb:INDex 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:PREamb:INDex?
Dependencies	If State is ON and Data is Auto-Configured Bits, then this setting is visible.
Preset	0
State Saved	Yes
Min	0
Max	63
Initial S/W Revision	A.20.01

PRACH Mask Index

Sets the PRACH mask index for RA initiation.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:PRACh:MASK:INDex <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI10:TX<seq>:PRACh:MASK:INDex?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:PRACh:MASK:INDex 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI10:TX1:PRACh:MASK:INDex?
Dependencies	If State is ON and Data is Auto-Configured Bits, then this setting is visible.
Preset	0
State Saved	Yes
Min	0
Max	15
Initial S/W Revision	A.20.01

DCI #11/PDCCH

DCI #11 (UL Power Control) transmission configuration.
Extends the base DCI/PDCCH template with Power Control and TPC Bits.

Refer to 3GPP TS 36.213.

DCI #11 is only available when the current component cell is the primary cell.

State

Turns the subframe state on or off.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>[:STATe]?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:STATe?
Preset	0
State Saved	Yes
Initial S/W Revision	A.20.01

Format

DCI Format type.

Refer to 3GPP TS 36.211, 36.212, and 36.213.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:FORMat FORMat3\|FORMat3a [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:FORMat?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:FORMat FORMat3 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:FORMat?
Dependencies	If State is ON and Data is Auto-Configured Bits , then this setting is visible.
Preset	FORMat3
State Saved	Yes
Initial S/W Revision	A.20.01

Data

Selects PN9, PN15 or Auto-Configured Bits. Click the > button displayed with the setting to make the value selection.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:DATa PN9\|PN15\|ACONfig [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:DATa?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:DATa PN9 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:DATa?
Dependencies	If State is ON then this setting is visible.
Preset	ACONfig
State Saved	Yes
Initial S/W Revision	A.20.01

Data User Defined

Set the user-defined bits for data.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:DATa:USER <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:DATa:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:DATa:USER "00000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:DATa:USER?
Notes	Use the Data Source Selection dialog box to select User Defined Bits.
Dependencies	If State is ON then this setting is visible.
Preset	"00000000"
State Saved	Yes
Initial S/W Revision	A.20.01

Data Size

Sets the payload data size (bits) for DCI.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:DATa:SIZe <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:DATa:SIZe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:DATa:SIZe 26 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:DATa:SIZe?
Dependencies	If State is ON then this setting is visible.
Preset	26
State Saved	Yes
Min	1
Max	100
Initial S/W Revision	A.20.01

RNTI

Radio Network Temporary Identifier.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:RNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:RNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:RNTi 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:RNTi?
Dependencies	If State is ON then this setting is visible.
Preset	1
State Saved	Yes
Min	0
Max	65535
Initial S/W Revision	A.20.01

Search Space

Sets the search space.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:SSPace?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:SSPace?
Choices	Common, USEP
Dependencies	If State is ON then this setting is visible.
Preset	COMMon
State Saved	Yes
Initial S/W Revision	A.20.01

Aggregation Level

Selects the aggregation level.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:AGGLevel 1\|2\|4\|8 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:AGGLevel?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:AGGLevel 4 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:AGGLevel?
Choices	1\|2\|4\|8 When Search Space is UE Specific, then Aggregation Level choices are 1,2,4,8. When Search Space is Common, then Aggregation Level choices are 4,8.
Dependencies	If State is ON then this setting is visible.
Preset	4
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

Candidate

Sets the DCI candidate number.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:CANDidate?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:CANDidate?
Range	0-7
Dependencies	If State is ON then this setting is visible.
Preset	0
State Saved	Yes
Min	0
Max	7
Initial S/W Revision	A.20.01

CCE Offset

Query only

CCE Offset is automatically calculated.

Refer to 3GPP TS 36.213.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:CCE:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:CCE:OFFSet?
Range	0-1023
Dependencies	If State is ON then this setting is visible.
Preset	0
State Saved	Yes
Min	0
Max	1023
Initial S/W Revision	A.20.01

Power Control

Selects power control target.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:POWer:CONTrol PUSCh\|PUCCh [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:POWer:CONTrol?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:POWer:CONTrol PUSCh RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:POWer:CONTrol?
Choices	PUSCH, PUCCH
Dependencies	If state is ON and Data is Auto-Configured Bits, then this setting is visible.
Preset	PUSCh
State Saved	Yes
Initial S/W Revision	A.20.01

TpcBits

TPC bits string for power control commands.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:TPC:BITS:USER <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI11:TX<seq>:TPC:BITS:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:TPC:BITS:USER "00000000000000000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI11:TX1:TPC:BITS:USER?
Dependencies	If State is ON and Data is Auto-Configured Bits, then this setting is visible.
Preset	"00000000000000000000"
State Saved	Yes
Initial S/W Revision	A.20.01

DCI #12/PDCCH

DCI #12 transmission configuration.
Uses the same base DCI/PDCCH template with different defaults (DataSize=1, CceOffset=12).

State

Turns the subframe state on or off.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:STATe ON\|OFF\|1\|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:STATe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:STATe?
Preset	0
State Saved	Yes
Initial S/W Revision	A.20.01

Data

Selects PN9 or PN15.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:DATa PN9\|PN15\|ACONfig [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:DATa?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:DATa PN9 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:DATa?
Dependencies	If State is ON then this setting is visible.
Preset	PN9
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Data User Defined

Sets the user-defined bits for data.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:DATa:USER <string> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:DATa:USER?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:DATa:USER "00000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:DATa:USER?
Dependencies	If State is ON then this setting is visible.
Preset	"00000000"
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Data Size

Sets the payload data size (bits).

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:DATa:SIZe <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:DATa:SIZe?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:DATa:SIZe 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:DATa:SIZe?
Dependencies	If State is ON then this setting is visible.
Preset	1
State Saved	Yes
Min	1
Max	100
Initial S/W Revision	A.20.01

RNTI

Radio Network Temporary Identifier.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:RNTi <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:RNTi?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:RNTi 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:RNTi?
Range	0-65535
Dependencies	If State is ON then this setting is visible.
Preset	1
State Saved	Yes
Min	0
Max	65535
Initial S/W Revision	A.20.01

Search Space

Sets the search space.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:SSPace COMM\|UESP [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:SSPace?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:SSPace UESP RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:SSPace?
Choices	Common, UE Specific
Dependencies	If State is ON then this setting is visible.
Preset	UE Specific
State Saved	Yes
Min	N/A
Max	N/A
Initial S/W Revision	A.20.01

Aggregation Level

Selects the aggregation level. Choices: 1, 2, 4, 8.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:AGGLevel 1\|2\|4\|8 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:AGGLevel?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:AGGLevel 1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:AGGLevel?
Choices	1, 2, 4, 8 When Search Space is UE Specific, then Aggregation Level choices are 1,2,4,8. When Search Space is Common, then Aggregation Level choices are 4,8.
Dependencies	If State is ON then this setting is visible.
Preset	1
State Saved	Yes
Min	1
Max	8
Initial S/W Revision	A.20.01

Candidate

Query only

Sets the DCI candidate number. Read-only for DCI #12.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:CANDidate?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:CANDidate?
Range	0-7
Dependencies	If State is ON then this setting is visible.
Preset	1
State Saved	Yes
Min	0
Max	7
Initial S/W Revision	A.20.01

CCE Offset

Query only

CCE Offset.

Refer to 3GPP TS 36.213.

seq = 1 to 40

SCPI Command	[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:DCI:PDCCh:DCI12:TX<seq>:CCE:OFFSet?
SCPI Example	RADio:LTEFdd:WAVeform:CCARrier:DLINk:DCI:PDCCh:DCI12:TX1:CCE:OFFSet?
Dependencies	If State is ON then this setting is visible.
Preset	0
State Saved	Yes
Min	0
Max	1023
Initial S/W Revision	A.20.01